亚洲国产精品久久,91精品欧美一区二区三区,少妇激情艳情综合小视频,97久久精品人人澡人人爽

Welcome to [ Wuxi Funecon Precision Mould Plastic Co., Ltd. ] website! Home| Sitemap| Email
Moulding Your Future

Enquiry:

138-6185-1071

138-6185-1071

What is the effect of too high temperature during injection molding

Injection molding is a very important process. As soon as the material enters the mold, the temperature of the melt drops rapidly and the density and viscosity of the melt increase continuously. The ability to compensate for the melt depends on the amount of holding pressure and the entire filling time at which the melt continues to transfer into the mold. This process continues until the gate is solidified and closed. Therefore, it can be considered that the holding pressure and the dwell time have a great relationship with the shrinkage at this stage. If the holding pressure is large and the dwell time is long, the shrinkage rate of the product is relatively low.
During the injection molding process, it is inevitable that the temperature will be extremely high, and there will be many bad effects when the temperature is high:
1. Thermal deformation of the machine: The moving parts with different thermal expansion coefficients in the hydraulic components are stuck due to their small training, which causes malfunction and affects the transmission precision of the hydraulic system, resulting in poor working quality of the components.
2. Reduce the viscosity of the oil: If the temperature rise of the injection molding machine is too high, the viscosity of the oil will decrease, the leakage will increase, and the volumetric efficiency of the pump and the efficiency of the entire system will be significantly reduced. As the viscosity of the oil is lowered, the oil film of the moving parts such as the spool is thinned and cut, and the frictional resistance is increased, resulting in an increase in wear.
3. Deformation of the rubber seal: If the temperature rise of the injection molding machine is too high, the rubber seal will be deformed, the aging failure will be accelerated, the sealing performance and service life will be reduced, and leakage will occur.
4. Accelerate oil oxidation and deterioration: When the temperature rise of the injection molding machine is too high, it will accelerate the oxidation and deterioration of the oil, precipitate the asphalt material, and reduce the service life of the hydraulic oil. The precipitate blocks the damper orifice and the slit valve port, causing the pressure valve to become stuck and unable to move, the metal pipe to be elongated and bent, or even broken.
5. The working quality of the components is deteriorated: if the temperature rise of the injection molding machine is too high, the working quality of the components will be deteriorated, the dissolved air in the oil will escape, and air pockets will be generated, resulting in a decrease in the working performance of the hydraulic system.
2018/08/02 10:12:52 6623 次

Hot News

Copy right of the 2018 Wuxi Funecon Precision Mould Plastic Co., Ltd. All Rights Reserved

无遮挡男女激烈动态图| 99国产成人综合久久精品| 秋霞网| 欧美一区二区精品在线播放| 中文字幕被公侵犯的漂亮人妻| 欧美另类精品一区二区三区| 91欧美精品激情在线观看最新| 在线成人精品国产区免费| 风韵多水的老熟妇,| 大乳丰满人妻中文字幕日本| 久久午夜夜伦鲁鲁片无码免费| 黑人巨大精品欧美一区二区免费| 亚洲日韩精品欧美一区二区一| 强开小婷嫩苞又嫩又紧视频韩国| 日本不卡在线一区二区三区视频| 国产精品99精品无码视亚| 被黑人伦流澡到高潮HN小说| 调教玩弄奶头乳夹开乳震动器| 国产日皮视频| 在线播放三级黄色日韩av| 中英字幕乱码在线观看| 亚洲中文无码AV永久不收费| 原来是电影神马在线观看| 亚洲AV成人无码久久精品老人| 国产精品无码久久久久久| 玩弄丰满少妇人妻视频| 噼里啪啦国语版在线观看| 丁香花在线观看免费观看图片| 一区二区三区免费视频播放器| 一区二区在线 | 欧洲| YES4444视频在线观看| 国产精品亚洲一区二区三区在线| 一区二区三区免费视频播放器| 年轻的妈妈5韩国电影| 久久精品A亚洲国产V高清不卡| 精品久久久久久综合日本| 日韩在线精品一区二区三区| 2021理论片一级| 蜜臀视频一区二区在线播放| 国产精品一区二区在线观看| 亚洲欧美国产国产一区二区|